# Stress and Strain-Definition, Curve or Diagram, Formula, Differences, For Different Material, PDF

Are you looking for Stress and Strain? So today we will study the Definition, Curve or Diagram, Formula, Differences, For Different Material of Stress-Strain. Here you will get the articles of Mechanical Engineering in brief with some key points and you will get to know an enormous amount of knowledge from It. So If you find this articles helpful, please let us know in the comment box, either if any correction required too, also let us know in the comment box.

## Stress and Strain:

### Definition:

In engineering, stress has been defined is:

when an external force applied to the object(made of an elastic material), they produce a change in shape and size of the object.

`Stress is defined as, the deformation force per unit area of the body or material.`
`Stress is the internal force(per unit area) associated with the strain.`
`It is ratio of force applied on the system to the per unit area of the body.`

To find the stress of an object which is displaced (after applying force on it). The formula is,

Stress(σ)= Force(F) / (A)Cross-sectional Area

Whereas, σ= Stress in N/M2 or Pascal.

F= Force applied on the system which is in Newton (N).

A= Cross-sectional area of the object in M2.

The types of stresses are like Tensile stress, Compressive stress, Torsional stress.

The Tensile stress is like pulling the material on each side or might one side as figures shown below, The Compressive stress is like pushing the material on each side or might one side as figures shown below, The Torsional stress is like there are two forces applied on the object and the forces are opposite to each other. The figure is shown below, Whereas Strain is defined as

`The ratio of change in length to the original length of an object or body is called as Strain.`
`Strain is relative change in shape or size of an object due to externally applied forces.`

To find the strain of an object which is displaced (after applying force on it). The formula is,

Strain(∈)= Change in length (Li) / Original length (L0)

The standard unit of strain is dimensionless. It has no units.

=Strain.

Li = Change in length in Meters.

L0 = Original length in Meters.

Related Articles:

Properties of Metals-Mechanical, Electrical, Thermal, Magnetic, Chemical properties, PDF

### Curves or Diagram:

This curve is a behavior of the material when it is subjected to load.

The stress-strain curve depends on two types of material.

1. Ductile Material:

Ductile materials are materials that can be plastically twisted with no crack. They have the tendency to hold the deformation that occurs in the plastic region.

The ductile material is- Aluminium, Copper, Steel and more.

2. Brittle Material:

A material is brittle if, when subjected to stress, it breaks without significant plastic deformation. Brittle materials absorb relatively little energy prior to fracture, even those of high strength.

The brittle material is- Cast Iron, Concrete, Some glass product and more.

To draw the stress-strain curve of any material the mechanical point or properties includes,

• Proportional Limit
• Elastic Limit
• Yield Point
• Ultimate Stress Point
• Breaking Point

Taking an example to understand the curve :

### Stress-Strain curve for Mild steel (Ductile Material): #### Young’s Modulus:

The Young’s modulus is defined as the ratio of the stress of the object to the strain of the object or body.

Young’s Modulus= Stress / Strain

The SI unit of  Young’s Modulus is N/M2 or Pascal.

#### Limit of proportionality or Proportionality limit (A):

The proportional limit is the point on the curve up to which the value of stress and strain remains proportional.

From the diagram point, A is the called the proportional limit point or it can also be known as the limit of proportionality.

The stress up to this point can be also be known as proportional limit stress.

#### Elastic limit:

Elastic limit is the limiting value of stress up to which the material is perfectly elastic.

#### Yield Stress (B-C):

• B-upper yield value
• C-lower yield value

Yield stress is defined as the stress after which material extension takes place more quickly with no or little increase in load. Point (B-C) is the yield point on the graph and stress associated with this point is known as yield stress.

#### Ultimate Stress Point (D):

Ultimate stress point is the maximum strength that material has to bear stress before breaking.

It can also be defined as the ultimate stress corresponding to the peak point on the stress-strain graph.

#### Breaking Stress Point or Fracture Point (E):

Breaking point or breaking stress or Fracture point is the point where the strength of material breaks.

The stress associated with this point known as breaking strength. On the stress-strain curve, point E is the breaking stress point or Fracture point.

Other Articles:

Jigs and Fixtures-Definition, Types, Differences, Factors to be considered in designing ,Advantages, Application, Material used

Brake System-Definition, Function, Types in details-Mechanical, Disc, Hydraulic, Power assisted brake

### Differences between Stress and Strain:

Stress is defined as a force that can cause a change in an object or a physical body while a strain is a change in the form or shape of the object or physical body on which stress is applied.

The stress can occur without strain, but strain cannot occur with the absence of stress.

The stress can be measured and has a unit of measure while strain does not have any unit and, therefore, cannot be measured.

A strain is an object’s response to stress while stress is the force that can cause strain in an object.

Stress comes from the Latin word “strictus” which means “to draw tight” while “strain” comes from the Latin word “stringere” which means “to bind tightly.”

Do you want to PDF? Join our WhatsApp or Telegram or facebook for Downloading the PDF.

Join our WhatsApp group: Engramritkumar Facebook

Join our telegram group:   Engramritkumar Telegram

Join our WhatsApp group: Engramritkumar WhatsApp

Reciprocating Pump-Main Parts, working Principle, Application, Advantages and Disadvantages, PDF

Today we have learned about Definition, Curve or Diagram, Formula, Differences, For Different Material. If I have missed something, kindly inform me through commenting. If you like this article, don’t forget to share it on social networks. Subscribe our website for more informative articles. Thanks for reading it. Thank you.

## 11 thoughts on “Stress and Strain-Definition, Curve or Diagram, Formula, Differences, For Different Material, PDF”

1. P Rajasekhar says:

I want full notes with understanding words of material science and metallurgy, manufacturing technology – 1

1. admin says:

Definitely, Keep in touch. I will update it.

2. guesh weldegebrial says:

good

1. admin says:

Thank You.

3. Assefa says:

Engineering is best

1. admin says:

Yes Definitely.

4. Lawal Olamide says:

Please I need PDF file of it
Thanks

1. admin says:

Please visit telegram or facebook group

5. Nilesh says:

How to get pdf link

1. admin says:

Connect with us on Telegram or facebook. Link is provided in articles.

6. Rajesh says:

Yyy

error: Content is protected !!